Sierra MC7455 vs EM7455: mPCIe or M.2 Packaging, Which One Should You Choose?
Table of Contents
One-sentence summary of the difference: if your board has an mPCIe slot, such as a legacy industrial router, choose the MC7455. If it has an M.2 slot, such as a modern business laptop or a new embedded motherboard, choose the EM7455. Both run the same Qualcomm MDM9230 chipset, so 4G performance is identical. What you actually need to compare is the packaging and hardware integration details.
The MC7455 is Sierra Wireless’s PCI Express Mini Card (mPCIe) module, while the EM7455 is its M.2 sibling in the same 74xx family. Both modules integrate LTE, UMTS, and GNSS positioning, and both use the Qualcomm MDM9230 baseband processor. Network speeds are identical as well: LTE Cat 6 with peak downlink of 300 Mbps (FDD) / 222 Mbps (TDD) and peak uplink of 50 Mbps (FDD) / 26 Mbps (TDD). This article extracts the hardware differences from the official specifications so you know exactly what to expect before you buy.
Technical references: Sierra Wireless official specifications, the AirPrime MC7455 Product Technical Specification and the AirPrime EM7455 Product Technical Specification. Compiled by Yopitek.
Quick Conclusion: How to Choose in 30 Seconds#
| Your scenario | Recommended module | One-line reason |
|---|---|---|
| Legacy industrial router / panel PC (mPCIe slot) | MC7455 | Native mPCIe packaging, plug in directly with no adapter |
| Business laptop / modern motherboard (M.2 slot) | EM7455 | M.2 WWAN Type 3042-S3-B, native match |
| Board has M.2 only, but you already own an MC7455 | Consider buying EM7455 or use an M.2-to-mPCIe adapter | Adapter solutions add enclosure-height and antenna connector complications |
| Board has mPCIe only, but you already own an EM7455 | Consider buying MC7455 or use an mPCIe-to-M.2 adapter | Check the mPCIe slot’s power and signal definitions carefully |
| Wide-temperature range and industrial certifications matter | Either one | ClassA/ClassB wide-temperature specs are the same; certification details below |
So what does this mean? For most users, the LTE capability of the MC7455 and EM7455 is exactly the same. Which module you choose is 90% determined by the slot on your board; the remaining 10% is the integration differences in power supply, antenna, and control pins. Let us look at that 10% in detail.
Common Point 1: Same Chipset, Same LTE Performance#
People often ask “which one is faster?” The answer is “they are equally fast,” because both the MC7455 and EM7455 carry the Qualcomm MDM9230.
The specifications are clear: based on this chipset, their LTE capabilities are fully equivalent:
- LTE Cat 6: downlink FDD 300 Mbps / TDD 222 Mbps; uplink FDD 50 Mbps / TDD 26 Mbps
- DC-HSPA+: up to 42 Mbps downlink; up to 5.76 Mbps uplink
- LTE bands: 1, 2, 3, 4, 5, 7, 8, 12, 13, 20, 25, 26, 29, 30, 41 (Band 41 is TDD)
- Downlink MIMO: 2x2, 4x2
- WCDMA bands: 1, 2, 3, 4, 5, 8
So what does this mean? If you are hesitating because you want faster 4G speeds, both modules deliver the same experience. What you should focus on instead is the hardware specification differences covered next.
Common Point 2: Identical GNSS Positioning#
Both modules integrate four-constellation GNSS: GPS, GLONASS, BeiDou, and Galileo, with identical positioning accuracy and time-to-fix figures in the specifications.
- Up to 30 channels tracked simultaneously.
- Hot start in 1 second, warm start in 29 seconds, cold start in 32 seconds (at -135 dBm signal level).
- Horizontal accuracy under 2 m (50%).
So what does this mean? For fleet management or industrial equipment that requires positioning, either module handles the job. The one thing to watch is the different antenna connector (covered later), so check your GNSS antenna cabling when swapping modules.
Key Difference 1: Form Factor (the Core Difference)#
The MC7455 is a PCI Express Mini Card (mPCIe), while the EM7455 is M.2. The edge-connector pin counts and keying are completely different, so the slots are not interchangeable. Do not get this wrong.
- MC7455: 52-pin EDGE connector, Type F2. Dimensions 50.95 x 30 x 2.75 mm, weight 8.7 g.
- EM7455: 67-pin EDGE (M.2 Slot B), WWAN Type 3042-S3-B. Dimensions 42 x 30 mm, thinner, weight 6.5 g.
So what does this mean? mPCIe is the legacy standard for industrial equipment, while M.2 is the current mainstream in laptops and new motherboards. Just look at the slot on your board. Forcing an adapter only adds complexity.
Key Difference 2: Different Supply Voltage (VCC) Standards#
The MC7455 has a typical VCC of 3.30 V, while the EM7455 has a typical VCC of 3.7 V. Both share the same minimum startup voltage of 3.135 V, but the upper tolerance limits differ significantly (3.60 V vs 4.4 V).
So what does this mean? If you plan to mount an EM7455 on an mPCIe slot with an adapter (which usually provides only 3.3 V), note that the EM7455’s power design is based on 3.7 V. The MC7455, by contrast, is designed to run on 3.3 V throughout. Before swapping modules, confirm that the supply is adequate (both modules draw a maximum of 1.5 A, with startup inrush reaching 2.2-2.5 A).
Key Difference 3: Antenna Connectors (U.FL vs MHF4)#
The MC7455 uses a Hirose U.FL antenna connector, while the EM7455 uses the smaller MHF4-compatible connector. The pigtail cables on the two sides cannot be shared directly.
- Both modules have 3 antenna connectors (Main, GNSS, Auxiliary).
- Both have a 50 Ohm coaxial impedance, with a recommended maximum cable loss of 0.5 dB.
So what does this mean? This is the most common pitfall when upgrading legacy equipment. You pull out the old MC7455 expecting the EM7455 on an adapter to work, only to find that the existing U.FL antenna cables do not latch onto the MHF4 connector. Plan for adapter cables in advance.
Key Difference 4: Different Control Signal Design#
The MC7455 controls the entire module with a single W_DISABLE_N pin. The EM7455 splits the functions, and the Full_Card_Power_Off# pin must be tied high, otherwise the module will not power on at all.
- MC7455: has SYSTEM_RESET_N, but the vendor specifically warns that it must not be installed in an mPCIe slot that carries PCIe signals, or the module may reboot repeatedly.
- EM7455: has separate main RF disable (W_DISABLE1#) and GNSS disable (W_DISABLE2#) pins.
So what does this mean? If you are building your own adapter, be careful: mPCIe slots often lack the complete power control signals the EM7455 needs, which can leave the module stuck in a powered-off state.
Key Difference 5: Number of Antenna Control Signals#
The MC7455 provides 3 antenna control signals (ANT_CTRL0:2), while the EM7455 provides 4 (ANTCTL0:3).
So what does this mean? If you are integrating an advanced tunable antenna solution, the EM7455’s extra signal gives more flexibility. For a standard fixed-antenna router, this difference can be ignored.
Which One Should You Choose?#
Core principle: check the slot first, then the surrounding integration.
For Hobbyists Repairing Their Own Equipment#
If you are simply repairing an industrial router or panel PC from a few years ago, the slot is almost certainly mPCIe. Just buy the MC7455. It plugs in directly, reuses the existing antenna cables, and avoids adapter complications. The only thing to verify: make sure that mPCIe slot carries pure USB signals (not PCIe).
For Enterprise Engineers Selecting for a Project#
For a chassis-lifetime-extension project (keeping the same motherboard), putting an MC7455 directly into the mPCIe slot is the fastest path. For a new platform design, most current motherboards use M.2, so go straight to the EM7455, switch the antenna connectors to MHF4, and follow the M.2 specification for power control.
Summary#
The MC7455 and EM7455 are like the same brain housed in different bodies. Since network speed, bands, and positioning capability are all identical, what you really need to confirm is: does your board take mPCIe or M.2? Is the supply voltage correct? Do the antenna connectors match? Sort out these points and you will not buy the wrong module.
FAQ#
Frequently Asked Questions
Which is faster, the MC7455 or the EM7455?
They are equally fast. Both use the same Qualcomm MDM9230 baseband processor, with LTE Cat 6 peak downlink of 300 Mbps (FDD) / 222 Mbps (TDD) and peak uplink of 50 Mbps (FDD) / 26 Mbps (TDD). The supported LTE bands are identical as well. The only real differences are packaging, power supply, and antenna connectors.
Can the MC7455 and EM7455 be used interchangeably in the same slot?
No. The MC7455 is a PCI Express Mini Card (mPCIe, 52-pin EDGE, Type F2), while the EM7455 is an M.2 module (WWAN Type 3042-S3-B, 67-pin EDGE). The edge-connector pin counts and keying are completely different, so the slots are not interchangeable. An adapter board is required, and you must verify power and antenna compatibility.
Should my board use the MC7455 or the EM7455?
It depends on the slot. Choose the MC7455 for the mPCIe slot of a legacy industrial router or panel PC, and the EM7455 for the M.2 slot of a business laptop or modern embedded motherboard. LTE performance is identical, so about 90% of the decision comes down to the slot on your board.
Can the EM7455 be installed in an mPCIe slot?
It can be installed with an adapter board, but note that the EM7455 is designed around a 3.7 V supply (an mPCIe slot usually provides only 3.3 V), and its antenna connectors are MHF4-compatible. Existing U.FL pigtail cables cannot be reused directly, so plan on adapter cables.
Call to Action (Sourcing)#
Need the MC7455 or EM7455, or unsure which slot your existing equipment uses? Yopitek is a professional industrial wireless solutions provider. We can help you confirm:
- Motherboard slot and module compatibility assessment
- Antenna connector adapters and cable matching
- Long-term stock and volume pricing
Email us at [email protected] or browse the Yopitek website for related products.