Sierra EM7565 Deep Dive: CBRS Private LTE and High Uplink Explained
Table of Contents
If you are running a lab project or building enterprise private LTE and CBRS networks, the EM7565 will come up in your shortlist. Here is the catch: getting named in every discussion does not mean you can plug it in and run CBRS out of the box.
This article skips marketing talk. We use a single reference: the Sierra Wireless official specification, the AirPrime EM7565 Product Technical Specification (Doc 41110788, Rev 8, October 2018). We walk through the chipset, data rates, bands, antennas, temperature, and certifications line by line, and we will be honest about the “pending regulatory approval” caveat in the spec. If you are an integrator or an engineer making a purchasing decision, this is the checklist you need.
Product page: EM7565 — Yopitek | Official spec: AirPrime EM7565 Product Technical Specification
EM7565 at a Glance#
The EM7565 is an M.2 WWAN cellular module from Sierra Wireless built on the Qualcomm MDM9250 chipset. It delivers LTE Cat 12 downlink (up to 600 Mbps) and Cat 13 uplink (up to 150 Mbps), with multi-constellation GNSS positioning on board.
Straight answers to the questions people ask most:
| Question | Straight answer |
|---|---|
| Can the EM7565 run a CBRS private network? | The spec does list LTE Band 48 (the 3.5 GHz CBRS band), but at the time Rev 8 was published it was marked “disabled, pending regulatory approval”. For commercial use, always check the current regulations and the latest official spec, and confirm the status with us before ordering. |
| How fast is the uplink? | Up to 150 Mbps (Cat 13); downlink peaks at 600 Mbps (Cat 12). |
| Who is it for? | Enterprise industrial routers and system integrators doing edge computing who need to push large amounts of data back to the cloud (that is where the fast uplink pays off). If you are a hobbyist building on a Raspberry Pi, an M.2-to-USB carrier board works too. |
| Does it include antennas? | No. The card has 3 small RF connectors (Main, GNSS, Auxiliary). You buy the antennas and design the routing yourself. |
Full EM7565 Spec Sheet: Straight from the Official Data#
Engineers like numbers. Every figure below comes from the Sierra Wireless official specification, with source line references recorded in the Verification Log at the end of the source document.
| Item | Specification | Source |
|---|---|---|
| Model | AirPrime EM7565 (Doc 41110788, Rev 8) | Spec cover |
| Form factor | M.2 (WWAN Type 3042-S3-B) | Spec p. 14 |
| Chipset | Qualcomm MDM9250 baseband processor | Spec p. 12 |
| Cellular standard | LTE: 3GPP Release 11; UMTS: 3GPP Release 9 | Spec p. 18 |
| Downlink peak | Cat 12, 3×CA, 256QAM: 600 Mbps (Cat 9: 450 Mbps) | Spec p. 12 |
| Uplink peak | Cat 13, 2×CA contiguous, 64QAM: 150 Mbps | Spec p. 12 |
| Carrier aggregation | DL LTE-FDD: 60 MHz; DL LTE-TDD: 60 MHz; UL LTE: 40 MHz (intraband contiguous) | Spec p. 15 |
| MIMO | Downlink 2×2 / 4×2 | Spec p. 12 |
| UMTS rates | DC-HSPA+ up to 42 Mbps downlink, 11 Mbps uplink | Spec p. 12 |
| LTE bands | B1/B2/B3/B4/B5/B7/B8/B9/B12/B13/B18/B19/B20/B26/B28/B29(DL)/B30(DL)/B32(DL)/B41/B42/B43/B46/B48/B66 (B42/43/48 marked disabled at publication) | Spec p. 42 |
| WCDMA bands | Band 1/2/4/5/6/8/9/19 | Spec p. 43–44 |
| Interfaces | USB 2.0 + USB 3.0; QMI, MBIM; AT commands | Spec p. 15, 28 |
| SIM | Dual SIM (1.8V or 3V), SIM sockets not included | Spec p. 29 |
| Antenna interface | 3 RF connectors: Main, GNSS, Auxiliary | Spec p. 37 |
| GNSS | GPS, GLONASS, Galileo, BeiDou, QZSS simultaneous tracking; 32 s cold start | Spec p. 47 |
| Dimensions | 42±0.15 × 30±0.15 mm | Spec p. 57 |
| Weight | 6.5 g | Spec p. 57 |
| Operating temperature | Class A: -30°C to +70°C; Class B: -40°C to +85°C (cooling and derating required) | Spec p. 14, 57 |
| Internal module temperature | Must stay below 90°C; keep below 80°C if possible | Spec p. 14 |
| Regulatory approvals | FCC (US), IC (Canada), NCC (Taiwan), MIC (Japan), RED (EU) and more | Spec p. 62 |
Heads up: these figures follow Rev 8 (October 2018). Firmware and certifications change over time. Before ordering, ask us for the latest official documents and re-confirm.
So Can You Build a CBRS Private Network with the EM7565?#
In short: the hardware lists support, but the firmware and regulatory picture depend on the current state.
The spec does include Band 48 (3550–3700 MHz) for CBRS. The “but” matters here: at the time Rev 8 was published, B42/B43/B48 were explicitly marked “disabled as of publication date, support pending regulatory approval”.
So we will not promise that it runs CBRS straight out of the box. If you are planning a CBRS private network, confirm three things: whether the latest firmware unlocks B48, whether it meets US FCC Part 96 certification at that time, and whether the full device passes OTA. When in doubt, check the latest status with us first.
Why Cat 12 Downlink + Cat 13 Uplink Matters for Your Project#
The headline feature is not the downlink. It is the uplink.
Phones mostly download (video streaming, social feeds). Industrial and IoT projects often do the opposite: push data back to the cloud. The EM7565 delivers Cat 13 uplink (up to 150 Mbps, 2×CA, 64QAM) and Cat 12 downlink (up to 600 Mbps, 3×CA, 256QAM).
That is a strong fit for uplink-heavy workloads: factory cameras streaming live video back to a control room, or sensor data from autonomous vehicles flooding to the cloud. If your project only needs occasional internet access for the device, a cheaper Cat 6 module (like the EM7455) is enough.
Which Bands Does the EM7565 Support?#
Short answer: 24 LTE bands (B1–B66) and 8 WCDMA bands. Mainstream bands for Taiwan and the Asia-Pacific region are covered.
LTE band breakdown:#
- Common bands: B1, B3, B7, B8, B28 (used by most carriers in Taiwan and Asia-Pacific).
- Downlink only: B29, B30 (Tx disabled), B32, B46 (LTE-LAA).
- Pending regulatory approval (at publication): B42, B43, B48 (CBRS).
If your project targets Taiwan, coverage is not a concern. If your lab needs a private network or special-band testing (like B48), do not order from the old spec sheet, ask about the current status first.
Three Antenna Connectors: RF Design Is on You#
The EM7565 has no built-in antennas. The host board must provide them. The card carries three small RF connectors: Main (primary Tx/Rx), Auxiliary (diversity/MIMO), and GNSS.
For LTE you need at least Main and Auxiliary to form a 2×2 MIMO setup. Connectors are I-PEX MHF4. Sierra recommends an antenna VSWR below 2:1 and radiated efficiency above 50%. If you are spinning your own PCB and routing antennas, budget time for RF testing.
GNSS: Cellular and Positioning in One Module#
If your project involves vehicles or logistics, this module covers you: it tracks five constellations (GPS, GLONASS, Galileo, BeiDou, QZSS) across up to 30 channels simultaneously. Cold start takes about 32 seconds, and it outputs standard NMEA 0183. You save the cost of a separate GPS module and the board space it would take.
Wide-Temperature Design: Built for Industrial Abuse#
Thermal shutdown is the biggest fear in industrial equipment. The EM7565 handles -30°C to +70°C under 3GPP standards, and with proper cooling it stretches to -40°C to +85°C (at reduced performance).
Lab tip: the spec says the internal module temperature (checkable with AT!PCTEMP) must never exceed 90°C and should stay below 80°C. If you bury the module in a small enclosure running full-speed uplink, add a thermal pad or a fan. Otherwise the protection mechanism throttles or shuts the module down.
Power and Power-Supply Design: Don’t Cheap Out on the Regulator#
The EM7565 runs on 3.135V to 4.4V (typically 3.3V). Current spikes at full speed and at power-on:
- Peak current: 1.3A (averaged over 100 µs)
- Maximum current: 1.5A
- Inrush current: 2.2A to 2.5A
When you design the board and pick a DC-DC buck or LDO, size for the 2.5A inrush. Do not look at the 2.8 mA standby figure and choose a regulator that cannot handle the load.
Regulatory and Certification Notes#
The spec lists compliance with FCC (US), NCC (Taiwan), RED (EU), plus GCF and PTCRB certifications. That saves real work when you bring a product to market. One reminder: these are module-level certifications. The full device you build still needs its own FCC or NCC testing to be legal.
Verdict: Should You Buy the EM7565?#
| Your requirement | A good fit? | Why |
|---|---|---|
| You need very high uplink speed | ✅ Excellent | The 150 Mbps Cat 13 uplink is built for this. |
| You want to test CBRS private networks | ⚠️ Hold on | Hardware supports B48, but confirm the latest firmware and regulatory status with us first. |
| You just need basic internet and file transfer | ❌ Overkill | A cheaper Cat 4 or Cat 6 module (like the EM7455) saves your budget. |
| Fleet management with precise positioning | ✅ Great fit | 4G plus five-constellation positioning in one module, no extra GPS part. |
Quick comparison: EM7565 vs EM7455#
| Item | EM7565 | EM7455 |
|---|---|---|
| Downlink | 600 Mbps (Cat 12, 3×CA) | 300 Mbps (Cat 6, 2×CA) |
| Uplink | 150 Mbps (Cat 13, 2×CA) | 50 Mbps (Cat 6) |
| Chipset | Qualcomm MDM9250 | Qualcomm MDM9230 |
Quick FAQ#
Frequently Asked Questions
Does the EM7565 support CBRS (Band 48) private networks?
The official spec sheet (Rev 8, Oct 2018) lists Band 48 (3550–3700 MHz, the CBRS band), but at publication it marks B42/B43/B48 as disabled pending regulatory approval. Any CBRS deployment must be checked against the latest official spec, current firmware, and the applicable regulatory status at the time.
How fast is the EM7565 uplink?
Uplink is LTE Cat 13 (2×CA contiguous, 64QAM) with a theoretical peak of 150 Mbps; downlink is Cat 12 (3×CA, 256QAM) with a theoretical peak of 600 Mbps. Real-world throughput depends on the base station, signal quality, and firmware.
Does the EM7565 have built-in antennas? How many do I need?
No. The module exposes 3 RF connectors: Main (Tx/Rx), GNSS, and Auxiliary (diversity/MIMO/GNSS). LTE requires at least a 2×2 MIMO external antenna system, and the antennas and cabling are your design responsibility.
What is the EM7565 operating temperature range?
Class A (3GPP compliant) -30°C to +70°C; Class B (non-3GPP) -40°C to +85°C with proper cooling and reduced operating parameters. The internal module temperature must stay below 90°C, ideally below 80°C.
Does the EM7565 work on Linux?
Yes. The USB interface supports QMI (Linux and Android) and MBIM (Windows 8.1/10 and Linux), plus a 3GPP TS 27.007 AT command interface and a Linux SDK. Actual driver support depends on your distribution and kernel version.
Talk to Us About Your Project#
This deep dive was put together by the engineering team at Yopitek. If you are selecting a 4G module for a lab, or your company needs volume pricing and antenna design support for the EM7565, reach out.
- EM7565 product page: https://yupitek.com/en/products/sierra/em7565/
- More Sierra models: https://yupitek.com/en/products/sierra/
- Email us: [email protected]