↓ Skip to main content
  1. Blog/

BVLOS Cellular Connectivity for Drones and Inspection Robots: How to Build Low Latency Backhaul

Table of Contents

The short version: to fly a drone beyond your line of sight, you need a 4G/5G module that handles video streaming, remote control and positioning all at once. If your drone runs on a 5G private network and needs top video throughput plus ultra accurate L1+L5 dual frequency positioning, pick the EM9191. If it is just an inspection robot crawling slowly around a factory, the cheap and reliable 4G module EM7565 is more than enough.

When a drone or robot leaves your line of sight (this is called BVLOS, Beyond Visual Line of Sight), the traditional remote controller in your hands stops working. At that point the machine can only rely on its onboard 4G/5G modem to reach a cell tower, send high resolution video back, and receive your joystick commands.

In this article we open up the Sierra Wireless official specification sheets and explain why these particular modules are so well suited to drones and robots, and how they achieve low latency.

Technical data source: Sierra Wireless official specification sheets (EM9190/EM9191, EM7565). Compiled by Yopitek.


30 Second Guide: Which Module Goes in a Drone or Robot?
#

ApplicationRecommended moduleWhy?
High end drone (needs a 5G private network)EM9191Supports 5G Sub-6 and 5G SA private network architecture, has the top tier LTE Cat 20 uplink speed, and includes built in L1+L5 high accuracy positioning.
High end drone (US market)EM9190The big brother of the EM9191, it adds mmWave support. But it is not needed in Taiwan.
Factory inspection robot (ground based)EM7565It is a 4G Cat 12 module, light and power efficient. Factory inspection does not need the 5G overkill. It is the best value.

How Is Low Latency Achieved? The Secrets in the Spec Sheet
#

Anyone who games knows ping (latency) matters. For a drone flying in the sky, latency can be a matter of life and death. The spec sheet will not tell you “latency in milliseconds”, but it contains these three weapons that dramatically cut latency:

  1. 5G SA (standalone) architecture: the EM919x supports the Option 2 SA architecture. That means the drone can connect directly to the 5G core network without routing through legacy 4G base stations. This is the most powerful latency reducer.
  2. QoS QCI priority control: the module supports 3GPP Release 15 QoS settings, so you can make flight control commands higher priority than video streaming. Even on a congested network, the machine will not lose control.
  3. Uplink carrier aggregation (UL CA) and 256QAM: video backhaul depends entirely on uplink speed. Both the EM919x and EM7565 can bond multiple bands together for uplink, and use the highest order 256QAM (EM919x) or 64QAM (EM7565) modulation so video streams stay smooth without stuttering.

Drone vs. Inspection Robot: Very Different Selection Logic
#

What flies in the sky and what crawls on the ground have completely different demands on the modem.

Drone: extremely sensitive to weight, heat and positioning
#

  • Weight is flight time: the EM9191 is 52 mm long and weighs 9 g; the EM7565 is 42 mm long and weighs 6.5 g.
  • Positioning accuracy: drones depend heavily on GPS. The EM919x has built in L1 + L5 dual frequency GNSS, which is far more accurate than traditional single frequency GPS and resists interference well.
  • Antenna count: the EM919x needs all 4 antennas connected to unlock its MIMO performance. When designing the drone chassis, you must budget space for those 4 antennas. If you choose the EM9190 and add mmWave antennas, weight and power draw get even scarier.

Inspection robot: sensitive to stability and cost
#

  • A robot crawls along the ground slowly and usually builds maps with a LiDAR, so it does not depend as deeply on GPS. The single frequency GPS built into the EM7565 is enough.
  • A robot has plenty of space and a big battery inside, but factory floors usually only have 4G coverage. In that case the EM7565 (Cat 12, 150 Mbps uplink) is already more than enough. There is no need to force a 5G module in.

Hardware Pitfalls to Check Before You Fly
#

If you are a hardware integration engineer, pay attention before you drop the module onto the board:

  1. Do not be fooled by mmWave: many people assume that buying 5G means buying the top of the line EM9190 to play with mmWave. In reality, mmWave has terrible penetration and there is almost no mmWave private network in Taiwan. For 99% of drones, the EM9191 with Sub-6 support is the perfect choice, and it saves you a pile of external antenna hassle.
  2. Watch out for overheating: the EM919x is a 5G beast with an internal temperature red line of 115°C (we recommend staying under 100°C). If a drone bakes in the summer sun at altitude and the module is sealed inside a plastic shell with no airflow, it will throttle and even drop the link.
  3. Do not skimp on antenna cables: the spec sheet requires cable loss under 0.5 dB with 50 ohm impedance. Pair a premium module with cheap night market antenna cables and your video quality will be painful to watch.

Conclusion
#

For a BVLOS connectivity project, the Sierra Wireless modules have already packaged video bandwidth, low latency architecture and high accuracy positioning into a single small M.2 card. If it flies, the budget is there, and you want a 5G private network, buy the EM9191 directly. If it crawls on the ground and only needs to stream 1080p reliably, the EM7565 is the worry free pick.


Quick FAQ
#

Frequently Asked Questions

Why does a BVLOS drone have to use a cellular connection?

Once the drone flies beyond visual line of sight, the remote controller signal is lost. At that point, a 4G/5G network is the only solution that provides wide area coverage, low latency control and high bandwidth video streaming.

What is the difference between the EM9190 and EM9191?

The EM9190 adds 5G mmWave support, but it requires power-hungry, space-consuming array antennas. In most regions without mmWave networks, the EM9191 with pure 5G Sub-6 is the right choice.

Which module suits an inspection robot?

For factory inspection, you usually only need to stream ordinary video back. The 4G EM7565 (Cat 12, 150 Mbps uplink) meets the requirement at a lower cost.


Ready to Buy (Call To Action)
#

Designing a communication board for a drone or an inspection robot? Not sure how to plan antennas and cooling? Yopitek offers the full Sierra Wireless module lineup plus hardware integration consulting services. Email us: [email protected] Browse the products: https://yupitek.com/en/products/sierra/